én-sugárzom

Feb 20, 2022 Hagyjon üzenetet

Két szabványos I{0}}sugárforma létezik:

I-beams are commonly made of szerkezeti acél but may also be formed from alumínium or other materials. A common type of I-beam is the hengerelt acél gerenda (RSJ)—sometimes incorrectly rendered as megerősített acél gerenda. angol and európai szabványok also specify Universal Beams (UBs) and Universal Columns (UCs). These sections have parallel flanges, as opposed to the varying thickness of RSJ flanges which are seldom now rolled in the UK. Parallel flanges are easier to connect to and do away with the need for tapering washers. UCs have equal or near-equal width and depth and are more suited to being oriented vertically to carry axial load such as columns in multi-storey construction, while UBs are significantly deeper than they are wide are more suited to carrying bending load such as beam elements in floors.

I-gerendák—I-beams engineered from wood with farostlemez and/or laminált furnér fűrészáru—are also becoming increasingly popular in construction, especially residential, as they are both lighter and less prone to warping than solid wooden gerendák. Aggodalomra ad okot azonban, hogy tűz esetén gyorsan elveszítik erejüket, ha nem védik őket.

Hajlításra alkalmas kialakítás 

A legnagyobb igénybevételek () egy hajlítás alatt álló gerendában a semleges tengelytől legtávolabbi helyeken vannak.

A beam under bending sees high stresses along the axial fibers that are farthest from the semleges tengely. A meghibásodás elkerülése érdekében a gerenda anyagának nagy részét ezeken a területeken kell elhelyezni. Viszonylag kevés anyagra van szükség a semleges tengelyhez közeli területen. Ez a megfigyelés az alapja az I-gerenda keresztmetszetének-; a semleges tengely a szövedék közepe mentén fut, amely viszonylag vékony lehet, és az anyag nagy része a karimákban koncentrálódhat.

The ideal beam is the one with the least cross-sectional area (and hence requiring the least material) needed to achieve a given keresztmetszeti tényező. Since the section modulus depends on the value of the tehetetlenségi nyomaték, a hatékony sugárnak anyagának nagy részének a semleges tengelytől a lehető legtávolabb kell lennie. Minél távolabb van egy adott anyagmennyiség a semleges tengelytől, annál nagyobb a szelvény modulusa, és így nagyobb hajlítónyomatéknak is ellenállhat.

When designing a symmetric I-beam to resist stresses due to bending the usual starting point is the required section modulus. If the allowable stress is  and the maximum expected bending moment is , akkor a szükséges szakaszmodulust adjuk meg3

where  is the moment of inertia of the beam cross-section and  is the distance of the top of the beam from the neutral axis (see gerenda elmélet for more details).

For a beam of cross-sectional area  and height , the ideal cross-section would have half the area at a distance  above the cross-section and the other half at a distance  below the cross-section.3 For this cross-section

Ezeket az ideális feltételeket azonban soha nem lehet elérni, mert fizikai okokból anyagra van szükség a hálóban, beleértve a kihajlás elleni védelmet is. Széles-peremgerendák esetén a szelvénymodulus hozzávetőleges

ami jobb a téglalap alakú gerendákkal és körgerendákkal elértnél.

Problémák 

Though I-beams are excellent for unidirectional bending in a plane parallel to the web, they do not perform as well in bidirectional bending. These beams also show little resistance to twisting and undergo sectional warping under torsional loading. For torsion dominated problems, dobozgerendák and other types of stiff sections are used in preference to the I-beam.

Formák és anyagok (USA) 

Rozsdás, szegecselt acél I{0}}gerenda

Az Egyesült Államokban a leggyakrabban említett I-gerenda a széles-karima (W). Ezek a gerendák karimákkal rendelkeznek, amelyek belső felületei területük nagy részén párhuzamosak. Az egyéb I-gerendák közé tartoznak az American Standard (S) alakúak, amelyekben a belső karimafelületek nem párhuzamosak, valamint a H-cölöpök (HP jelöléssel), amelyeket általában cölöpalapként használnak. Széles-karimaformák ASTM A992 minőségben állnak rendelkezésre,4 which has generally replaced the older ASTM grades A572 and A36. Ranges of yield strength:

  • A36: 36,000 psi (250 MPa)

  • A572: 42,000–60,000 psi (290–410 MPa), with 50,000 psi (340 MPa) the most common

  • A588: Similar to A572

  • A992: 50,000–65,000 psi (340–450 MPa)

A legtöbb acéltermékhez hasonlóan az I{0}}gerendák is gyakran tartalmaznak újrahasznosított anyagot.

Szabványok 

A következő szabványok határozzák meg az I{0}}gerendás acélprofilok alakját és tűréseit:

Európai szabványok 

  • EN 10024, Hot rolled taper flange I sections – Tolerances on shape and dimensions.

  • EN 10034, Structural steel I and H sections – Tolerances on shape and dimensions.

  • EN 10162, Cold rolled steel sections – Technical delivery conditions – Dimensional and cross-sectional tolerances

AISC kézikönyvszerkeszteni

The American Institute of Steel Construction (AISC) publishes the Steel Construction Manual for designing structures of various shapes. It documents the common approaches, Megengedett szilárdságú tervezés (ASD) and Terhelési és ellenállási tényező tervezése (LRFD), (starting with 13th ed.) to create such designs.

Egyéb 

Megnevezés és terminológia 

Széles-karima I-gerenda.
  • In the Egyesült Államok, steel I-beams are commonly specified using the depth and weight of the beam. For example, a "W10x22" beam is approximately 10 in (254 mm) in depth (nominal height of the I-beam from the outer face of one flange to the outer face of the other flange) and weighs 22 lb/ft (33 kg/m). Wide flange section beams often vary from their nominal depth. In the case of the W14 series, they may be as deep as 22.84 in (580 mm).6

  • In Kanada, steel I-beams are now commonly specified using the depth and weight of the beam in metric terms. For example, a "W250x33" beam is approximately 250 millimetres (9.8 in) in depth (height of the I-beam from the outer face of one flange to the outer face of the other flange) and weighs approximately 33 kg/m (22 lb/ft; 67 lb/yd).7 I-beams are still available in U.S. sizes from many Canadian manufacturers.

  • In Mexikó, steel I-beams are called IR and commonly specified using the depth and weight of the beam in metric terms. For example, a "IR250x33" beam is approximately 250 mm (9.8 in) in depth (height of the I-beam from the outer face of one flange to the outer face of the other flange) and weighs approximately 33 kg/m (22 lb/ft).8

  • In India I-beams are designated as ISMB, ISJB, ISLB, ISWB. ISMB: Indian Standard Medium Weight Beam, ISJB: Indian Standard Junior Beams, ISLB: Indian Standard Light Weight Beams, and ISWB: Indian Standard Wide Flange Beams. Beams are designated as per respective abbreviated reference followed by the depth of section, such as for example ISMB 450, where 450 is the depth of section in millimetres (mm). The dimensions of these beams are classified as per IS:808 (as per BIS).idézet szükséges

  • In the Egyesült Királyság, these steel sections are commonly specified with a code consisting of the major dimension (usually the depth){{0}}x-the minor dimension-x-the mass per metre-ending with the section type, all measurements being metric. Therefore, a 152x152x23UC would be a column section (UC = universal column) of approximately 152 mm (6.0 in) depth 152 mm width and weighing 23 kg/m (46 lb/yd) of length.9

  • In Ausztrália, these steel sections are commonly referred to as Universal Beams (UB) or Columns (UC). The designation for each is given as the approximate height of the beam, the type (beam or column) and then the unit metre rate (e.g., a 460UB67.1 is an approximately 460 mm (18.1 in) deep universal beam that weighs 67.1 kg/m (135 lb/yd)).5

Celluláris gerendák 

Celluláris gerendák are the modern version of the traditional "öntött gerenda" which results in a beam approximately 40–60 percent deeper than its parent section. The exact finished depth, cell diameter and cell spacing are flexible. A cellular beam is up to 1.5 times stronger than its parent section and is therefore utilized to create efficient large span constructions.10